Kit Installation | Kit Description | Material Specifications
Before starting your application, double check the pattern for accuracy.
Lay the film face down above your application area, and remove the liner. Spray plenty of application solution (25% isopropyl alcohol and 75% water) on the film and back where the part will be applied.
Turn the film over so the adhesive side is down, and place it lightly on the vehicle.
Lift film from vehicle and wet surface again. Then pull tight without stretching and align part. Starting at your center point, work your way outward, completing half at a time. Remember : You cannot use too much of the solution.
Once a section is in position, squeegee out excess solution and any bubbles.
For recessed areas or compound curves, rewet the adhesive and slowly squeegee again with firm pressure.
Once you are finished, the protection is virtually invisible!
Our Invisible Bras are engineered to fit the exact shape of your car, truck, SUV, motor home, boat or other recreational vehicle precisely and securely, making it hard to tell that the invisible bra has been applied. Star Shield Armor Kits are nearly invisible because we use larger pieces that cover more area with fewer seams.
This is the most basic kit available. This kit includes the hood, end caps and mirrors as shown below.
This is our most widely used kit because of its complete front-end coverage which includes the pieces in the "A Kit" plus the entire front bumper.
This kit provides complete all around coverage and includes the pieces in the "A Kit" and "B Kit" plus top door pillars, cab top, door handles and door edge guards.
For the Professional Applicator
Published with the permission of 3M Corporation. Information Provided by 3M Product Bulletin 1-45.
| General Description |
3M Scotchcal™ High Performance Protective Films are noted for their overall excellent performance. These rugged, yellowing-resistant urethane films protect against stone chips, bug damage, abrasion and weathering while allowing a vehicle's color brilliance to show through and its design intent to be maintained. Approved by Automotive OEMs, these durable films are flexible, comfortable and easy to apply. PUL 0612 and PUL 1212 are available in rolls of varying widths. |
| Product Construction |
| PUL 0612 |
 |
| PUL 1212 |
 |
|
| Shelf Life |
It is recommended that temperatures of 13 degrees C - 32 degrees C (55 degrees RF- 90 degrees F) and 44 percent - 55 percent relative humidity be maintained in the film storage location. Film should be used within one year of purchase. |
| Expected Effective Performance Characteristics |
Performance statements are based upon representative experience from testing throughout the United States; however, actual performance will be determined by substrate selection and preparation, exposure conditions, and maintenance of the marking. When applied, or when processed and applied according to 3M recommended procedures, this product will conform to 3M's specifications for two years following purchase from 3M. |
|
Physical and Chemical characteristics |
Values given are typical and are not for use as specifications. If a specification is desired, a custom specification will be prepared. Any requests for a specification should be submitted through your local 3M representative. |
|
Performance Properties |
These values represent typical data when tested to major OEM urethane specifications and should not be used for product approval. |
| |
Results |
| Performance Test and Condition |
PUL 0612 |
PUL 1212 |
| Tensile MPa (PSI) |
12 (1740) |
12 (1740) |
| Elongation |
200 Percent |
200 Percent |
| Peel Adhesion |
| Initial State - 20 min @ 23 deg. C (73 deg. F) N/m (lb/in) |
600 (3.4) |
600 (3.4) |
| Room Temp - 72 hrs @ 23 deg. C (73 deg. F) N/m (lb/in) |
700 (4.0) |
700 (4.0) |
| Heat Resistance - 168 hrs @70 deg. C (158 deg. F) N/m (lb/in) |
700(4.0) |
700(4.0) |
| Moisture Resistance - 168 hrs @ 35 deg C (95 deg F) |
700(4.0) |
700(4.0) |
| Thermal Cycle |
700(4.0) |
700(4.0) |
|
Environmental Simulation |
| Acid Resistance |
Pass |
Pass |
| Fuel Resistance |
Pass |
Pass |
| Heat Resistance - 168 hrs @ 70 deg. C (158 deg F) |
Pass |
Pass |
Moisture Resistance - 168 hrs @ 35 deg C (95 deg F)
100% R.H. - 2 hrs.@70 deg C (158 deg F) |
Pass |
Pass |
| Thermal Cycle |
Pass |
Pass |
| Solvent Resistance |
Pass |
Pass |
| Shrinkage |
<.1 Percent |
<.1 Percent |
| Gravelometer (SAE J400) |
No Ruptures |
No Ruptures |
|
| Outdoor Deck Weathering |
Arizona 45 deg. South Facing (unbacked)
- No objectionable gloss loss or change, adhesion loss,
film crackup, or crazing. |
24 months |
Less than 10 percent gloss loss and no more than 2.5 De color change |
Less than 10 percent gloss loss and no more than 2.5 De color change |
Florida 5 Deg South Facing (unbacked)
-No objectionable gloss loss or change, adhesion loss,
film crackup, or crazing. |
24 months |
Less than 10 percent gloss loss and no more than 2.5 De color change |
Less than 10 percent gloss loss and no more than 2.5 De color change |
|
| Product Characteristics |
| Adhesive: |
Acrylic PSA |
| Liner: |
White - Bleached paper with release coating |
| Max Service Temp: |
Film softens above 67 deg C (150 deg F) |
|
|
